Proface APL3000B - Node Box PC Manuale Utente

3/6HULHV+DUGZDUH0DQXDO

9PL3000 Series Model NamesThe term “PL3000” Series refers to the following numbers:The panel computer consists of the box-type built-in computer (cont

Chapter 5 Installation and Wiring5-95.2 Installing/removing the front module and the control boxBefore operating the internal switches or replacing th

PL3000 Series Hardware Manual5-10(2) Disconnect the flexible cable.(3) Unscrew the four (4) attachment screws on the top and bottom faces of the front

Chapter 5 Installation and Wiring5-115.2.2 PL-3600K/3700∗/3900T Series Removing the front module and the control boxRemove the control box from the f

PL3000 Series Hardware Manual5-12(4) Slide the control box in direction shown by the arrow.(5) Lift the control box and remove the front module tabs f

Chapter 5 Installation and Wiring5-135.3 Peripheral Device InstallationA wide variety of devices manufactured by Pro-face such as optional units, DIM

PL3000 Series Hardware Manual5-145.3.2 Attachment of the Power Switch CoverWhen using the AC type, the included power switch cover needs to be install

Chapter 5 Installation and Wiring5-155.3.3 Removal of Expansion Slot CoverWhen installing the main memory or the expansion board, remove the expansion

PL3000 Series Hardware Manual5-165.3.4 Main Memory Installation(1) Remove the PL unit’s expansion slot cover.(2) The DIM modules are installed in the

Chapter 5 Installation and Wiring5-17(3) Insert the expansion board (commercial type) into the expansion board connector, and secure it in place using

PL3000 Series Hardware Manual5-185.3.6 HDD/SSD Unit Installation(1) Unscrew the attachment screws (2) from the HDD slot to remove the slot cover.(2) H

10Package ContentsPackage contents of the PL-3000B Series (control box)The following items are included in the PL unit’s package. Before using the PL

Chapter 5 Installation and Wiring5-195.3.7 CF Card Insertion/Removal Inserting the CF Card(1) Unscrew the attachment screws (2) from the CF Card cove

PL3000 Series Hardware Manual5-20(2) Insert the CF Card firmly into the CF Card slot, and check that the eject button pops out.(3) Install the CF Card

Chapter 5 Installation and Wiring5-215.3.8 Connecting USB Cable ClampThis clamp is used to prevent the USB cable connected to the USB Interface of the

PL3000 Series Hardware Manual5-22 Removing the USB Cable ClampTo remove the clamp from the USB cables, push down on the clamp strap’s clip to release

Chapter 5 Installation and Wiring5-235.4 Wiring PrecautionsThis section describes the procedures and precautions for wiring power cords.5.4.1 Connecti

PL3000 Series Hardware Manual5-24 Spring-type Power ConnectorUse the following procedure to connect a spring-type power connector to all compatible p

Chapter 5 Installation and Wiring5-25Connecting the Power Cord(1) Confirm that power is not supplied to the PL unit.(2) Push the Opening button with a

PL3000 Series Hardware Manual5-26WiringWhen connecting the power cord, use the following items. (Made by Phoenix Contact*1.) Power Connector (Right-an

Chapter 5 Installation and Wiring5-275.4.2 Connecting the Power SupplyThis section describes the precautions for supplying a power voltage.• If the su

PL3000 Series Hardware Manual5-285.4.3 GroundingThis section describes the precautions for grounding the PL unit.• When supplying power to the PL unit

11Package contents of the PL-3600∗/3700∗/3900T SeriesThe following items are included in the PL unit’s package. Before using the PL, please check tha

Chapter 5 Installation and Wiring5-295.4.4 I/O Signal Line Placement• Input and output signal lines must be separated from the power control cables fo

PL3000 Series Hardware Manual5-30

6-16 Maintenance1. Cleaning the Fan Filter2. Periodic Check Points3. Replacing the Installation Gasket4. Replacing the Backlight5. Replacing the Inter

PL3000 Series Hardware Manual6-26.1 Cleaning the Fan FilterSince excessive dirt and dust in the filter of the PL’s electric fan can potentially affect

Chapter 6 Maintenance6-3(3) Clean the filter completely. If stubborn dirt or stains are present, wash the filter with a neutral detergent.(4) After re

PL3000 Series Hardware Manual6-46.2 Periodic Check PointsTo keep your PL unit in its best condition, please inspect the following points periodically.

Chapter 6 Maintenance6-56.3 Replacing the Installation GasketThe installation gasket provides protection against dust and moisture. Installation Gask

PL3000 Series Hardware Manual6-6.• The gasket must be inserted correctly into the groove for the PL’s moisture resistance to be equivalent to IP65f.•

Chapter 6 Maintenance6-76.4 Replacing the Backlight6.4.1 PL-3600∗ SeriesPL units use a long-life type backlight. The actual life of the backlight howe

PL3000 Series Hardware Manual6-8 PreparationPlease have the following ready beforehand.• Replacement backlight (Model:CA3-BLU12-01)• One pair of clea

12This unit has been carefully packed, with special attention to quality. However, should you find anything damaged or missing, please contact your lo

Chapter 6 Maintenance6-9(5) Loosen the backlight attachment screw.(6) Remove the tape on the backlight connector and disconnect the cable of the backl

PL3000 Series Hardware Manual6-10(7) Lift the backlight unit up and then pull it out slowly as shown below.(8) Insert the tip of a new backlight, and

Chapter 6 Maintenance6-116.4.2 PL-3700∗ SeriesPL units use a long-life type backlight. The actual life of the backlight however, will vary depending o

PL3000 Series Hardware Manual6-12 PreparationPlease have the following ready beforehand.• Replacement backlight (Model: CA7-BLU15-01 (Set of two ligh

Chapter 6 Maintenance6-13(5) Loosen the four screws from the LCD holder.(6) Loosen the upper and lower backlight attachment screws.(7) Remove the tape

PL3000 Series Hardware Manual6-14(8) Lift the LCD holder up as shown in the figure and pull the cable in the direction of the arrow. The back-light un

Chapter 6 Maintenance6-156.4.3 PL-3900T SeriesPL units use a CFL, long-life type backlight. The actual life of the backlight however, will vary depend

PL3000 Series Hardware Manual6-166.5 Replacing the Internal Battery6.5.1 Replacing the Battery for Backup of Internal Clock DataThe PL unit has an int

Chapter 6 Maintenance6-17 Battery Replacement Procedure(1) With the panel computer, remove the control box from the front module before replacing the

PL3000 Series Hardware Manual6-18

13Installation prerequisites for standards• UL listed products• c-UL listed products• Product ListUL/c-UL File No.: E220851, E210412For the detailed c

7-17 Built-in Options1. DVD Drive Unit2. Battery UnitThis chapter provides supplementary information on built-in options available for the PL unit.

PL3000 Series Hardware Manual7-27.1 DVD Drive UnitThis section provides information on the PL unit in which our DVD drive unit or DVD multi drive unit

Chapter 7 Built-in Options7-3 System Set SwitchPL which has a built-in DVD drive unit has the System Set Switch (SW1) No.8 already correctly set befo

PL3000 Series Hardware Manual7-47.1.2 Dimensions (DVD drive unit built-in)The following dimensional drawings apply to the control box in which the DVD

Chapter 7 Built-in Options7-5 Dimensions of the 4 slot unit243 [9.57]12 [0.47]277 [10.91]289 [11.38]214 [8.43]TopUnit: mm [in.]Right sideFront(Panel

PL3000 Series Hardware Manual7-6 Dimension of the Screw HolesWhen vertically mounting the PL-3000B series unit in which the DVD drive unit is built-i

Chapter 7 Built-in Options7-77.2 Battery UnitThis section provides information on PL unit with a built-in battery unit.7.2.1 CautionBattery Mainten

PL3000 Series Hardware Manual7-8Avoid leaving the battery in high temperature places such as direct sunlight, inside a sun-heated car, near water, or

Chapter 7 Built-in Options7-97.2.2 SpecificationThe specifications differ between models with or without the built-in battery unit.This section decrib

PL3000 Series Hardware Manual7-107.2.3 Backup BatteryThe battery unit is equipped with a Ni-H battery for backup. Charging timeIt takes 15 hours for

14<Cautions>Be aware of the following items when building the PL into an end-use product:PL-3000B series• The PL unit is approved as an open-typ

Chapter 7 Built-in Options7-117.2.5 Installation prerequisites for standardsUL/c-UL standards differ between models with or without the built-in batte

PL3000 Series Hardware Manual7-12

15<Control Drawing of USB I/F on PL's Front Module>The information below concerns the use of the USB I/F located on the PL unit's fron

16CE MarkingThe following units are CE marked product that conforms to EMC directives and Low Voltage Directives.The following units are CE marked pro

17About RevisionThe nameplate on the PL has the revision code of the PL. In the example below, the asterisk, which is placed at the “A” position, show

18ContentsPreface... 1Essential Saf

1PrefaceThank you for purchasing Pro-face’s PL3000 Series Graphic Logic Controller Interface (Hereafter referred to as the “PL unit”).Before operating

19Chapter 4 Dimensions4.1 PL-3000B Series... 4-24.1.1 Dimens

205.2 Installing/removing the front module and the control box ... 5-95.2.1 PL-3600T Series...

1-11 Overview1. System Design2. Accessories3. Power SupplyThis chapter describes peripheral devices that can be connected to PL unit.

PL3000 Series Hardware Manual1-21.1 System DesignThe following diagram illustrates the standard range of items that can be connected to PL unit.PLInsi

Chapter 1 Overview1-31.2 AccessoriesAll accessories listed here are produced by Pro-face.1.2.1 Optional ItemsProduct Name Model No. DescriptionDIM mod

PL3000 Series Hardware Manual1-41.2.2 Maintenance ItemsProduct Name Model No.Supported PL modelDescriptionInstallation FastenerAPL-ATFB-01PL-3000B ser

Chapter 1 Overview1-51.3 Power SupplyThe PL has three kinds of power supply states: Non-energized, Normal State, and Soft OFF State*1. Each state is o

PL3000 Series Hardware Manual1-6

2-12 Part Names and Functions1. PL-3000B Series2. PL-3600T/3700T Series3. PL-3600K/3700K Series4. PL-3900T SeriesThis chapter describes the name and f

PL3000 Series Hardware Manual2-22.1 PL-3000B SeriesA: Hardware reset switch (RESET)Restarts the PL unit during normal operation status.In the Soft OFF

2Essential Safety PrecautionsAll safety-related procedures stated in this document must be followed to operate the PL correctly and safely. Be sure to

Chapter 2 Part Names and Functions2-3K: Power LED / RAS status lamp (POWER)L: Disk access lamp (DISK)M: Serial interface (COM1)D-Sub 9-pin plug type.R

PL3000 Series Hardware Manual2-4R: Fan coverSystem fan insideS: System fanA fan for cooling the PL unitT: Power connectorU: Power switchAC type only.V

Chapter 2 Part Names and Functions2-52.2 PL-3600T/3700T SeriesA: Power LED / RAS Status Lamp (POWER)B: Disk Access Lamp (DISK)C: Front CoverD: Hardwar

PL3000 Series Hardware Manual2-6I: Expansion slotFor expansion board (PCI). 2 slots or 4 slots.J: Expansion slot coverExpansion slot cover is removed

Chapter 2 Part Names and Functions2-7S: RAS interface (RAS)D-Sub 9-pin socket type.T: CF Card interface (CF CARD)IDE-type connection*1.CF Card (Type I

PL3000 Series Hardware Manual2-82.3 PL-3600K/3700K SeriesA: Power LED / RAS Status Lamp (POWER)B: Disk Access Lamp (DISK)C: Front CoverD: Hardware Res

Chapter 2 Part Names and Functions2-9M: Mouse pointer2-button mouseN: DVI-I interface (DVI-I)For analog RGB output only. *1DVI-I 29 pin socket type.O:

PL3000 Series Hardware Manual2-10W: Disk access lamp (DISK)X: Serial interface (COM1)D-Sub 9-pin plug type.RS-232C, RS-422, RS-485 Changeover.CI (RI)/

Chapter 2 Part Names and Functions2-112.4 PL-3900T SeriesA: Power LED / RAS Status Lamp (POWER)B: Disk Access Lamp (DISK)C: Front CoverD: Hardware Res

PL3000 Series Hardware Manual2-12I: Expansion slotFor expansion board (PCI). 2 slots or 4 slots.J: Expansion slot coverExpansion slot cover is removed

3HandlingWiringMaintenanceDo not use the PL as a warning device for critical alarms that can cause serious operator injury, machine damage or can halt

Chapter 2 Part Names and Functions2-13S: RAS interface (RAS)D-Sub 9-pin socket type.T: CF Card interface (CF CARD)IDE-type connection*1.CF Card (Type

PL3000 Series Hardware Manual2-14

3-13 Specifications1. General Specifications2. Function Specifications3. Interface Specifications4. Internal Switches SpecificationsThis chapter descr

PL3000 Series Hardware Manual3-23.1 General Specifications3.1.1 Electrical SpecificationsPower SupplyDC type AC typeInput Voltage DC24V AC100 to 240VR

Chapter 3 Specifications3-33.1.2 Environmental Specifications PhysicalSurrounding Air Temperature0 to 50°C: without HDD *15 to 50°C: with HDD *1*1 It

PL3000 Series Hardware Manual3-4• Using the Hard Disk in an environment that is excessively hot and/or humid will shorten the disk’s usage lifetime. A

Chapter 3 Specifications3-53.1.3 Structural SpecificationsPL-3000B SeriesPL-3600∗ SeriesPL-3700∗ SeriesPL-3900T SeriesInstallationGroundingAC type: Pr

PL3000 Series Hardware Manual3-6 WeightSeriesWeight2 slot type (unit only) 4 slot type (unit only)PL-3000B Series 6.0kg [13.2lb] max. (unit only) 7.5

Chapter 3 Specifications3-73.2 Function Specifications3.2.1 Performance SpecificationsCPU Intel® CoreTM Duo 2.0 GHz Intel® Celeron® M 440 1.86GHzL2 C

PL3000 Series Hardware Manual3-8 Additional Memory CombinationsWhen adding more memory, it is recommended to install it in the combinations shown bel

4InstallationWiringMaintenanceUnit DisposalGeneral Safety PrecautionsBe sure all cable connectors are securely attached to the PL unit. A loose connec

Chapter 3 Specifications3-9 Current load per port Also, provide the expansion slots so that the external load power does not exceed the values descri

PL3000 Series Hardware Manual3-103.3 Interface SpecificationsThis section describes the specifications of each interface of the PL Series unit. Seria

Chapter 3 Specifications3-11RS-422RS-485Pin Arrangement Pin No.RS-422Signal Name Direction Description1 RDA Input Receive Data A(+)2 RDB Input Receive

PL3000 Series Hardware Manual3-12 Serial Interfaces (COM2/COM3/COM4)This interface is used to connect an RS-232C serial cable. A D-sub 9-pin plug con

Chapter 3 Specifications3-13 RAS InterfacesD-sub 9 pin socket connector• Be sure to use only the rated voltage level when using pin #1 (DC+12V) for e

PL3000 Series Hardware Manual3-14 General Purpose Signal Input (DIN 0, 1)Input Voltage DC12V to 24VInput Method Sink / Source InputInput Current 10mA

Chapter 3 Specifications3-15 General Purpose Signal Output (DOUT 0, 1)Rated Voltage DC12V to 24VMaximum Load Current 120mA/pointOut Voltage Drop1.5V

PL3000 Series Hardware Manual3-163.4 Internal Switches SpecificationsThe internal switches are mounted on the bottom face of the control box and the r

Chapter 3 Specifications3-17SW5 *1DVI Cable Selection Switch–Set to opposite side of the Q symbol. (FP-DV01-100 is not supported)Toggles between supp

PL3000 Series Hardware Manual3-18 System Set SwitchSwitch No.Description ON OFFFactory SettingsNotes1 Internal setting Reserved Reserved OFF Do not c

5LCD Panel Usage Precautions• The LCD panel’s liquid contains an irritant. If the panel is damaged and any of this liquid contacts your skin, immedi-a

Chapter 3 Specifications3-19 Serial Mode Select SwitchSwitch No.Description ON OFFRS-232C RS-422RS-485(The data is not automatically controlled via t

PL3000 Series Hardware Manual3-20Serial Mode Select Switches (SW4 to SW10) operate as shown in the circuit diagram below.*1*1 Set switches number 9 an

Chapter 3 Specifications3-21 DVI Cable Selection SwitchWhen connecting Pro-face FP3000 Series to PL-3000B Series unit, use the FP-DV01-100 (10m) Pro-

PL3000 Series Hardware Manual3-223.4.2 Internal switches of the front module. Touch Panel Set SwitchSwitch LocationSwitch NameFactorySettingsDescript

4-14 Dimensions1. PL-3000B Series2. PL-3600T Series3. PL-3600K Series4. PL-3700T Series5. PL-3700K Series6. PL-3900T SeriesThis chapter describes dime

PL3000 Series Hardware Manual4-24.1 PL-3000B SeriesThe PL-3000B Series can be installed in any of the following three methods: vertical, horizontal, o

Chapter 4 Dimensions4-3 Vertical mountingUnit: mm [in.]FrontSide153 [6.02]243 [9.57]Top141±0.4 [5.55±0.02]125 [4.92]261 [10.39]12 [0.47]277 [10.91]28

PL3000 Series Hardware Manual4-44.1.2 Dimensions of the 4 slot Unit (Installation fasteners attached) Horizontal mounting or wall mountingUnit: mm [i

Chapter 4 Dimensions4-5 Vertical mountingUnit: mm [in.]FrontSide204 [8.03]Top192±0.4 [7.56±0.02]176 [6.93]243 [9.57]261 [10.39]Enlarged view of the s

PL3000 Series Hardware Manual4-64.1.3 Cable Attached DimensionsUnit: mm [in.]*1 The measurement in the figure above is the distance the cable connecto

6• When the same image is displayed on the PL unit’s screen for a long period, an afterimage may appear when the image is changed. This is an LCD cha

Chapter 4 Dimensions4-74.1.4 Dimensions of the Screw HolesUse the following dimension drawings to drill the attachment bracket’s attachment screw hole

PL3000 Series Hardware Manual4-84.2 PL-3600T Series4.2.1 Dimensions of the 2 slot Unit (Installation fasteners attached)Unit: mm [in.]338 [13.31]295 [

Chapter 4 Dimensions4-94.2.2 Dimensions of the 4 slot Unit (Installation fasteners attached)Unit: mm [in.]218 [8.58]338 [13.31]295 [11.61]250 [9.84]2

PL3000 Series Hardware Manual4-104.2.3 Cable Attached DimensionsUnit: mm [in.] *1*1 This measurement is from the panel cut opening when the AC power s

Chapter 4 Dimensions4-114.2.4 Panel Cut DimensionsUnit: mm [in.]4.2.5 Installation FastenersUnit: mm [in.]• Please read "5.1 Installation (page 5

PL3000 Series Hardware Manual4-124.3 PL-3600K Series4.3.1 Dimensions of the 2 slot Unit (Installation fasteners attached)Unit: mm [in.]TopFrontSide425

Chapter 4 Dimensions4-134.3.2 Dimensions of the 4 slot Unit (Installation fasteners attached)Unit: mm [in.]TopFront Side425 [16.73]404 [15.91]218 [8.5

PL3000 Series Hardware Manual4-144.3.3 Cable Attached DimensionsUnit: mm [in.] *1*1 When the AC power supply connector (straight) is used, this is the

Chapter 4 Dimensions4-154.3.4 Panel Cut DimensionsUnit: mm [in.]• Please read "5.1 Installation (page 5-2)" before designing the Panel Cut.•

PL3000 Series Hardware Manual4-164.3.5 Installation FastenersUnit: mm [in.]16.6 [0.65]11 [0.43]16 [0.63]31 [1.22]M6ø10 [0.39]

7Information SymbolsThis manual uses the following icons:About the ManualsFor the detailed information on PL series, refer to the following manuals.•

Chapter 4 Dimensions4-174.4 PL-3700T Series4.4.1 Dimensions of the 2 slot Unit (Installation fasteners attached)Unit: mm [in.]404 [15.91]356 [14.02]8

PL3000 Series Hardware Manual4-184.4.2 Dimensions of the 4 slot Unit (Installation fasteners attached)Unit: mm [in.]404 [15.91]356 [14.02]8 [0.31]383

Chapter 4 Dimensions4-194.4.3 Cable Attached DimensionsUnit: mm [in.]*1*1 When the AC power supply connector (straight) is used, this is the clearance

PL3000 Series Hardware Manual4-204.4.4 Panel Cut DimensionUnit: mm [in.]4.4.5 Installation FastenersUnit: mm [in.]• Please read "5.1 Installation

Chapter 4 Dimensions4-214.5 PL-3700K Series4.5.1 Dimensions of the 2 slot Unit (Installation fasteners attached)Unit: mm [in.]TopDISPLAY AREA CENTERPR

PL3000 Series Hardware Manual4-224.5.2 Dimensions of the 4 slot Unit (Installation fasteners attached)Unit: mm [in.]TopDISPLAY AREA CENTERPRODUCTCENTE

Chapter 4 Dimensions4-234.5.3 Cable Attached DimensionsUnit: mm [in.]*1*1 When the AC power supply connector (straight) is used, this is the clearance

PL3000 Series Hardware Manual4-244.5.4 Panel Cut DimensionUnit: mm [in.]4.5.5 Installation FastenersUnit: mm [in.]• Please read "5.1 Installation

Chapter 4 Dimensions4-254.6 PL-3900T Series4.6.1 Dimensions of the 2 slot Unit (Installation fasteners attached)Unit: mm [in.]460 [18.11]419 [16.5]441

PL3000 Series Hardware Manual4-264.6.2 Dimensions of the 4 slot Unit (Installation fasteners attached)Unit: mm [in.]460 [18.11]419 [16.5]441 [17.36]39

8PL3000 Series Model Name IndicationModel nameAPL3*00-* * a0 No display6 12.1-inch display: SVGA (800 x 600 dots)7 15-inch display: XGA (1024 x 768 d

Chapter 4 Dimensions4-274.6.3 Cable Attached DimensionsUnit: mm [in.]*1*1 When the AC power supply connector (straight) is used, this is the clearance

PL3000 Series Hardware Manual4-284.6.4 Panel Cut DimensionsUnit: mm [in.]4.6.5 Installation FastenersUnit: mm [in.]• Please read "5.1 Installatio

5-15 Installation and Wiring1. Installation2. Installing/removing the front module and the control box3. Peripheral Device Installation4. Wiring Preca

PL3000 Series Hardware Manual5-25.1 InstallationThis section describes the procedures and precautions for installing the PL units.5.1.1 PL-3000B Serie

Chapter 5 Installation and Wiring5-3• For easier maintenance, operation, and improved ventilation, be sure to install the PL at least 50mm [1.97in.] a

PL3000 Series Hardware Manual5-4 Creating Screw HolesCreate the correct sized openings required to install the PL, using the installation dimensions

Chapter 5 Installation and Wiring5-55.1.2 PL-3600∗/PL-3700∗/PL-3900T SeriesThis section describes the procedures and precautions for installing the PL

PL3000 Series Hardware Manual5-6Installation Requirements• For easier maintenance, operation, and improved ventilation, be sure to install the PL at

Chapter 5 Installation and Wiring5-7 Installing the PL(1) Insert the PL into the panel cut, as shown. (2) Insert each fastener’s hook into the slot o

PL3000 Series Hardware Manual5-8(3) Insert each of the fasteners, as shown. Be sure to pull the fastener back until it is flush with the rear of the a